(1) Adjustment of the delivery organization:
When transporting books of different specifications, in order to ensure proper delivery of the books, the position of the books should be adjusted accordingly. The adjustment is very convenient, only need to manually drive the car, so that the connecting screw between the connecting block and the long link of the book feeder is located at the adjusting hole on the machine back plate, then loosen the screw and adjust the connection block and the long link of the book feeding The corresponding position of the room can achieve the purpose of adjusting the delivery position. When the book delivery position is appropriate, tighten the screws.
(2) Adjustment of the book receiving institution:
In the process of receiving books, the gap between the two book-receiving wheels should be adjusted according to the thickness of the book. The spacing is too large and the books cannot be sent to the bookshelf; the spacing is too small, and the book cannot pass the book-collecting wheel or Crush the book. When adjusting, loosen the locking handle and pull the handle to adjust the spacing between the two rows of receiving wheels. Then lock; the correct position of the receiving wheel, the receiving guide board and the receiving belt in the axial direction directly affects the orderliness of the books. When using adjustments, make sure that the center of gravity of the book is in the middle of the book receiving and receiving books. Books of general specifications must be transported through the middle of two pairs of receipts and two receipts, and large-size books are better delivered through three to four pairs of pickups and three to four receipts. The adjustment method is very simple. As long as the top wire on the two parts of the book receiving wheel and the book receiving guide board is loosened, the book receiving wheel and the book receiving guide board can be arbitrarily moved in the axial position, and after the ideal state is reached, the top is tightened. wire.
(3) Adjustment of the tight hook mechanism:
According to the changes in the specifications of the bound book, the centers of the two nails are required to be adjusted accordingly. When adjusting, loosen the lock nut, and then the bottom plate of the hook can move freely in the horizontal direction. When the ideal state is achieved, the lock nut can be locked. In the vertical direction, if the claws are lifted too high, the book will be crushed; the lift will be too low and the bound book will not be secure. First overall adjustment: Loosen the nuts on both ends of the pusher rod, and then turn the hook pusher to adjust the position of the lifting frame. Then, the lifting height of the tight hooks can be changed. When the requirements are met, tighten the two nuts. The heights of the tight hooks are the same and the adjustment is completed. Otherwise, the adjustments are performed separately: Loosen the locking screw, rotate the adjusting screw, and adjust the screw to drive the lifting plate to change the height of the tight hook.
In use, if there is a phenomenon that the wire is caught between the bottom plate of the hook and the tight claws, it can be removed by simply sliding the handle up and down twice.
(4) Adjustment of stapler:
In order to adapt to binding a variety of specifications and books, you need to adjust the bound hand. When the staple reaches its highest position, turn the M16 Allen screw on the staple. Turn counterclockwise and the bound hand is raised. Turn clockwise and the bound hand falls. The arrow indicates the value of the scale label on the bound hand, which is the thickness of the bound book.
(5) Adjustment of the binding head:
A:Adjustment of unequal lengths of two nails: When adjusting the length of two nails, first loosen the fastening screw and adjust the adjustable screw. If the clockwise direction rotates, the bound left foot will be shortened; After the screw rotates counterclockwise, gently tap the U-shaped head so that the adjustable screw abuts against the head shell. Then the length of the left staple will be lengthened. When the two nails are adjusted to the same length, tighten the screw lock. Can be tight.
B: Adjustment of the length of the feeding wire: According to the thickness of the bound book, the length of the feeding wire must be adjusted accordingly. When adjusting, loosen the screw and pull up the cover of the machine head to increase the length of the feeding wire. Pushing down the cover of the head will shorten the length of the feeding wire.
When transporting books of different specifications, in order to ensure proper delivery of the books, the position of the books should be adjusted accordingly. The adjustment is very convenient, only need to manually drive the car, so that the connecting screw between the connecting block and the long link of the book feeder is located at the adjusting hole on the machine back plate, then loosen the screw and adjust the connection block and the long link of the book feeding The corresponding position of the room can achieve the purpose of adjusting the delivery position. When the book delivery position is appropriate, tighten the screws.
(2) Adjustment of the book receiving institution:
In the process of receiving books, the gap between the two book-receiving wheels should be adjusted according to the thickness of the book. The spacing is too large and the books cannot be sent to the bookshelf; the spacing is too small, and the book cannot pass the book-collecting wheel or Crush the book. When adjusting, loosen the locking handle and pull the handle to adjust the spacing between the two rows of receiving wheels. Then lock; the correct position of the receiving wheel, the receiving guide board and the receiving belt in the axial direction directly affects the orderliness of the books. When using adjustments, make sure that the center of gravity of the book is in the middle of the book receiving and receiving books. Books of general specifications must be transported through the middle of two pairs of receipts and two receipts, and large-size books are better delivered through three to four pairs of pickups and three to four receipts. The adjustment method is very simple. As long as the top wire on the two parts of the book receiving wheel and the book receiving guide board is loosened, the book receiving wheel and the book receiving guide board can be arbitrarily moved in the axial position, and after the ideal state is reached, the top is tightened. wire.
(3) Adjustment of the tight hook mechanism:
According to the changes in the specifications of the bound book, the centers of the two nails are required to be adjusted accordingly. When adjusting, loosen the lock nut, and then the bottom plate of the hook can move freely in the horizontal direction. When the ideal state is achieved, the lock nut can be locked. In the vertical direction, if the claws are lifted too high, the book will be crushed; the lift will be too low and the bound book will not be secure. First overall adjustment: Loosen the nuts on both ends of the pusher rod, and then turn the hook pusher to adjust the position of the lifting frame. Then, the lifting height of the tight hooks can be changed. When the requirements are met, tighten the two nuts. The heights of the tight hooks are the same and the adjustment is completed. Otherwise, the adjustments are performed separately: Loosen the locking screw, rotate the adjusting screw, and adjust the screw to drive the lifting plate to change the height of the tight hook.
In use, if there is a phenomenon that the wire is caught between the bottom plate of the hook and the tight claws, it can be removed by simply sliding the handle up and down twice.
(4) Adjustment of stapler:
In order to adapt to binding a variety of specifications and books, you need to adjust the bound hand. When the staple reaches its highest position, turn the M16 Allen screw on the staple. Turn counterclockwise and the bound hand is raised. Turn clockwise and the bound hand falls. The arrow indicates the value of the scale label on the bound hand, which is the thickness of the bound book.
(5) Adjustment of the binding head:
A:Adjustment of unequal lengths of two nails: When adjusting the length of two nails, first loosen the fastening screw and adjust the adjustable screw. If the clockwise direction rotates, the bound left foot will be shortened; After the screw rotates counterclockwise, gently tap the U-shaped head so that the adjustable screw abuts against the head shell. Then the length of the left staple will be lengthened. When the two nails are adjusted to the same length, tighten the screw lock. Can be tight.
B: Adjustment of the length of the feeding wire: According to the thickness of the bound book, the length of the feeding wire must be adjusted accordingly. When adjusting, loosen the screw and pull up the cover of the machine head to increase the length of the feeding wire. Pushing down the cover of the head will shorten the length of the feeding wire.
Vertical Blinds Shape will be different with fauxwood venetian blinds, The width can be make it to 5 Meter, There are two open operate style, for the small window that you can choose single open operate style vertical blinds, for the large window that you can choose double open operate way style. you can just open one side, another side you can close when you don't want to the sunshine through into the full house. it is not only safety, but also operate convenience. In the Summer, make the house more cool, In the winter, make the room more harmony.
Vertical Blinds
Chain Control Vertical Blinds,Cordless Vertical Blinds,Wand Control Vertical Blinds,Printed Vertical Blinds,White Pvc Vertical Blinds
Dongguan Xindayuan Window Covering Products Co., Ltd. , http://www.xyndaxchina.com